Toyota Land Cruiser 2007 Manual Download Page 56

Page: 56 / 308

TUMBLING SECOND SEAT

1. Lower the outer head restraint to the

lowest position and pull up the cen-
ter head restraint. Unlock the seat-
back and fold it down.

Tumbling the rear seats will enlarge the
luggage compartment. See “Cargo and
luggage” on page 257 for precautions
when loading luggage.

2. Unlock the seat cushion. Swing the

whole seat up and forward.

3. Hook the strap.

When returning the second seat to its
original position, put the holding strap into
the hole.

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands

Toyota Land Cruiser 2007, Manual

Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands