Toyota Land Cruiser 2007 Manual Download Page 150 | Manualshive

Page: 150 / 308

background image

136

If the system fails to reset, the light will
remain flashing.

(f) Malfunction Indicator Lamp

This lamp comes on when the ignition
key is turned to the “ON” position and
goes off after the engine starts. This
means that the warning light system is
operating properly.

If the lamp remains on, or the lamp
comes on while driving, first check the
followings.

D

Empty fuel tank

If the fuel tank is empty, refuel immedi-
ately.

D

Loose fuel tank cap

If the fuel tank cap is loose, securely
tighten it.

These cases are temporary malfunctions.
The malfunction indicator lamp will go off
after taking several driving trips.

If the lamp will not go off even after sev-
eral trips, contact your Toyota dealer as
soon as possible.

If the lamp will not go off even after
the several trips...

or

If the fuel tank is not empty or the fuel
tank cap is not loose...

D

There is a problem somewhere in the
engine, emission control system, elec-
tronic throttle control system, automatic
transmission electrical system or warn-
ing light system itself.

Contact your Toyota dealer as soon as
possible to service the vehicle.

If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.

At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your vehicle
checked by your Toyota dealer as soon as
possible.

Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, the system may not be
recovered until the engine is stopped and
the ignition key is turned to “ACC” or
“LOCK” position.

CAUTION

Be especially careful to prevent erro-
neous pedal operation.

Emissions Inspection and Maintenance
(I/M) programs

Your vehicle may not pass a state emis-
sion inspection if the malfunction indicator
lamp remains on. Contact your Toyota
dealer to check your vehicle’s emission
control system and OBD (On−Board Diag-
nostics) system before taking your vehicle
for the inspection.

For details, see “Emissions Inspection and
Maintenance (I/M) programs” on page 316.

(g) Low Fuel Level Warning Light

This light comes on when the fuel level
in the tank becomes nearly empty. Fill up
the tank as soon as possible.

«
...
148
149
150
151
152
...
»

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Reviews:

No comments

Related manuals for Land Cruiser 2007

Brand: Jeep Pages: 42

Brand: Jeep Pages: 44

Brand: Cadillac Pages: 20

Brand: Jeep Pages: 7

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 354

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 10

2013 Escalade ESV

Brand: Cadillac Pages: 524

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Cadillac Pages: 450

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

Brand: Cadillac Pages: 78

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands