Toyota Land Cruiser 2007 Manual Download Page 293

Page: 293 / 308

345

—Headlights

73c005a

1. Open the hood.

Left−hand headlight: Remove the
washer inlet.

Be careful not to spill the washer fluid
over the “NORMAL” level.

Do not place the washer inlet on the en-
gine or battery.

2. Left−hand headlight and right−hand

head light (high beam):
Turn the bulb base counterclockwise
to the front of the vehicle.

Right−hand headlight (low beam):
Turn the bulb base clockwise to the
front of the vehicle.

3. Pull the bulb out of the bulb base.

If the connector is tight, wiggle it.

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands

Toyota Land Cruiser 2007, Manual

Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands