Toyota Land Cruiser 2007 Manual Download Page 294

Page: 294 / 308

346

4. Left−hand headlight and right−hand

headlight (high beam):
Install the bulb base by turning it
clockwise to the front of the vehicle.

Right−hand headlight (low beam):
Install the bulb base by turning it
counterclockwise to the front of the
vehicle.

Left−hand headlight: Remove the
washer inlet.

Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.

—Front fog lights

1. Turn the bulb base counterclockwise

to the front of the vehicle as shown.

2. Pull the bulb out of the bulb base.

If the connector is tight, wiggle it.

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands

Toyota Land Cruiser 2007, Manual

Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands