Toyota Corolla 2007 Operating Manual Download Page 92 | Manualshive

Page: 92 / 295

background image

’07 Corolla_U (L/O 0608)

84

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

To change the steering wheel angle,
hold the steering wheel, push down the
lock release lever, tilt the steering
wheel to the desired angle and return
the lever to its original position.

CAUTION

Do not adjust the steering wheel
while the vehicle is moving. Doing
so may cause the driver to mishan-
dle the vehicle and an accident may
occur resulting in death or serious
injuries.

After adjusting the steering wheel,
try moving it up and down to make
sure it is locked in position.

Adjust the mirror so that you can just
see the side of your vehicle in the mir-
ror.

Be careful when judging the size or dis-
tance of any object seen in the outside
rear view mirror on the passenger’s side
because it is a convex mirror. Any object
seen in a convex mirror will look smaller
and farther away than when seen in a flat
mirror.

Tilt steering wheel

Outside rear view mirrors—

«
...
90
91
92
93
94
...
»

Summary of Contents for Corolla 2007








































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2007

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: Kia Pages: 10

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: PEUGEOT Pages: 249

Brand: Kuda Pages: 3

Brand: Honda Pages: 85

Brand: Hyundai Pages: 11

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

2005 JR41 Stratus

Brand: Dodge Pages: 293

Brand: v.link Pages: 12

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Brink Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands