manualshive.com logo in svg

Toyota Corolla 2007, Operating Manual

The 2007 Toyota Corolla Pocket Reference Manual is a comprehensive and user-friendly manual that provides essential information and instructions for owners. Easily downloadable and free of charge from our website, this manual is a must-have for all Corolla owners seeking detailed guidance and support for their vehicle.

Share
Download
background image

’07 Corolla_U (L/O 0608)

262

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

The tires on your Toyota have built−in
tread wear indicators to help you
know when the tires need replace-
ment. When the tread depth wears to
1.6 mm (0.06 in.) or less,  the indica-
tors will appear. If you can see the
indicators in two or more adjacent
grooves, the tire should be replaced.
The lower the tread, the higher the
risk of skidding.

The effectiveness of snow tires is
lost if the tread wears down below
4 mm (0.16 in.).

If you have tire damage such as
cuts, splits, cracks deep enough to
expose the fabric, or bulges indi-
cating internal damage, the tire
should be replaced.

If a tire often goes flat or cannot be
properly repaired due to the size or
location of a cut or other damage, it
should be replaced. If you are not
sure, consult with your Toyota dealer.

If air loss occurs while driving, do not
continue driving. Driving even a short
distance can damage a tire beyond
repair.

Any tires which are over 6 years
old must be checked by a qualified
technician even  if damage is not
obvious.

Tires deteriorate with age even if they
have never or seldom been used.

This applies also to the spare tire and
tires stored for future use.

REPLACING YOUR TIRES

When replacing a tire, use a tire of
the same size and construction,
and the same or greater maximum
load as the originally installed
tires.

Using any other size or type of tire
may seriously affect handling, ride,
speedometer/odometer calibration,
ground clearance, and clearance be-
tween the body and tires or snow
chains.

Check that the maximum load of the
replaced tire is greater than 1/2 of the
Gross Axle Weight Ratings (GAWR)
of either the front axle or the rear
axle, whichever is greater. As for the
maximum load of the tire, see the load
limit at maximum cold tire inflation
pressure mentioned on the sidewall
of the tire, and as for the Gross Axle
Weight Ratings (GAWR), see the Cer-
tification Label.

For details about the side wall of the
tire and the Certification Label, see
pages 182 and 184.

Summary of Contents for Corolla 2007








































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2007

Jabra TOUR Get Started preview
TOUR
Brand: Jabra Pages: 10
AccuAir AA-4397 Installation Manual preview
AA-4397
Brand: AccuAir Pages: 40
Peak PKC0RG Owner'S Manual preview
PKC0RG
Brand: Peak Pages: 10
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Brand: Genesis Pages: 3
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
Camcar 40108 Mounting Instructions preview
40108
Brand: Camcar Pages: 6
ABL eMH3 Quick Start Manual preview
eMH3
Brand: ABL Pages: 4
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Brand: Volkswagen Pages: 80
U & Me Brothers LK-168A Manual preview
LK-168A
Brand: U & Me Brothers Pages: 6
Van Guard VG273 Fitting Instructions preview
VG273
Brand: Van Guard Pages: 3
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Brand: Billien Pages: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Brand: Lexus Pages: 28
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Brand: Griffin Technology Pages: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Brand: Mitsubishi Pages: 919
v.link CI-VL2-PC-HSD Manual preview
CI-VL2-PC-HSD
Brand: v.link Pages: 19
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Brand: Nav TV Pages: 11
Volvo 2009 S40 Owner'S Manual preview
2009 S40
Brand: Volvo Pages: 286

Brands by name

Popular brands

Load more brands