Toyota Corolla 2007 Operating Manual Download Page 87

Page: 87 / 295

’07 Corolla_U (L/O 0608)

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

2. To remove the booster seat, press the

buckle release button and allow the
belt to retract.

Follow the procedure below for a child
restraint system that requires the use
of a top strap.

Anchor brackets

Symbol

Use the anchor brackets on the luggage
compartment to attach the top strap.

Anchor brackets are installed for each
rear seating position.

This symbol indicates the locations of the
anchor brackets.

—Using a top strap

Summary of Contents for Corolla 2007








































































































































































































































































































Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands

Toyota Corolla 2007, Operating Manual

Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands