Toyota Corolla 2007 Operating Manual Download Page 267 | Manualshive

Page: 267 / 295

background image

’07 Corolla_U (L/O 0608)

259

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Keep your tire inflation pressures
at the proper level.

The recommended cold tire inflation
pressures, tire sizes and the com-
bined weight of occupants and cargo
(vehicle capacity weight) are de-
scribed on page 280 and 284. They
are also on the tire and loading infor-
mation label.

You should check the tire inflation
pressure every two weeks, or at least
once a month. And do not forget the
spare!

The following instructions for
checking tire inflation pressure
should be observed:

The pressure should be
checked only when the tires are
cold. If your vehicle has been
parked for at least 3 hours and has
not been driven for more than 1.5
km or 1 mile since, you will get
an accurate cold tire inflation pres-
sure reading.

Always use a tire pressure
gauge.

The appearance of a tire

can be misleading. Besides, tire
inflation pressures that are even
just a few pounds off can degrade
ride and handling.

Take special care when adding
air to the compact spare tire.
The smaller tire size can gain
pressure very quickly. Add com-
pressed air in small quantities and
check the pressure often until it
reaches the specified pressure.

Checking tire inflation
pressure

«
...
265
266
267
268
269
...
»

Summary of Contents for Corolla 2007








































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2007

Titanium Series

Brand: Fass Pages: 13

Brand: iDataLink Pages: 30

Brand: Kia Pages: 419

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

DLD Wide Range II

Brand: VDO Pages: 84

TravelCharge Companion GO-Plus

Brand: Wagan Pages: 3

Brand: MULTILIFT Pages: 62

Brand: BrandMotion Pages: 6

Brand: Volvo Pages: 123

Brand: Jeep Pages: 292

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands