Toyota Corolla 2007 Operating Manual Download Page 111

Page: 111 / 295

’07 Corolla_U (L/O 0608)

103

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

If the indicator or buzzer comes on...

Do this.

(h)

Take vehicle to Toyota dealer.
If brake system warning light is also on, stop immediately and contact Toyota dealer.

(i)

Close all doors.

(j)

Take vehicle to Toyota dealer immediately.

(k)

Adjust tire inflation pressure and turn off warning light by pushing reset switch for a
few seconds. If warning light remains, contact Toyota dealer.

(l)

Add washer fluid.

(m)

Take vehicle to Toyota dealer.

(n)

Replace engine oil.

Summary of Contents for Corolla 2007








































































































































































































































































































Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands

Toyota Corolla 2007, Operating Manual

Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands