manualshive.com logo in svg

Toyota Corolla 2007, Operating Manual

The 2007 Toyota Corolla Pocket Reference Manual is a comprehensive and user-friendly manual that provides essential information and instructions for owners. Easily downloadable and free of charge from our website, this manual is a must-have for all Corolla owners seeking detailed guidance and support for their vehicle.

Share
Download
background image

’07 Corolla_U (L/O 0608)

265

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

TIRE CHAIN SELECTION

Use the tire chains of correct size and
type.

Use SAE Class “S” type radial tire chains
except radial cable chains or V−bar type
chains.

Regulations regarding the use of tire
chains vary according to location or
type of road, so always check local reg-
ulations before installing chains.

CHAIN INSTALLATION

Install the chains on the front tires as
tightly as possible. Do not use tire
chains on the rear tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).

When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.

If wheel covers are used, they will be
scratched by the chain band, so remove
the covers before putting on the chains.

CAUTION

Do not exceed 50 km/h (30 mph) or
the chain manufacturer’s recom-
mended speed limit, whichever is
lower.

Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.

Avoid sharp turns or locked−wheel
braking, as use of chains may ad-
versely affect vehicle handling.

When driving with chains installed,
be sure to drive carefully. Slow
down before entering curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.

NOTICE

Do not attempt  to use a tire chain on
the compact spare tire, as it may re-
sult in damage to the vehicle as well
as the tire.

WHEN TO REPLACE YOUR WHEELS

If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.

If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.

WHEEL SELECTION

When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.

This must be observed on compact spare
tire, too.

Correct replacement wheels are available
at your Toyota dealer.

A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.

Replacing wheels

Summary of Contents for Corolla 2007








































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2007

CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Yakima SkyBox 12 Installation Instructions Manual preview
SkyBox 12
Brand: Yakima Pages: 6
Yakima HoldUp Plus2 Manual preview
HoldUp Plus2
Brand: Yakima Pages: 18
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Brand: Front Runner Pages: 5
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Brand: Mitsubishi Pages: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Brand: Cadillac Pages: 442
Audi 2011 A3 Sportback Pricing And Specification Manual preview
2011 A3 Sportback
Brand: Audi Pages: 29
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Brand: SNIPER Pages: 2
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Brand: NavInc Pages: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Brand: E&G Classics Pages: 3
Metra Electronics 99-7803G Wiring Instructions preview
99-7803G
Brand: Metra Electronics Pages: 2
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
Thule 1597 Instructions preview
1597
Brand: Thule Pages: 4
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Brand: Car-Interface Pages: 23
Metra Electronics 99-3305 Installation Instructions Manual preview
99-3305
Brand: Metra Electronics Pages: 12
Van Guard VG162S Fitting Instructions preview
VG162S
Brand: Van Guard Pages: 3
Blue Bird TC/2000 Owner'S Manual preview
TC/2000
Brand: Blue Bird Pages: 111

Brands by name

Popular brands

Load more brands