Toyota Corolla 2007 Operating Manual Download Page 110

Page: 110 / 295

’07 Corolla_U (L/O 0608)

102

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

If the indicator or buzzer comes on...

Do this.

(a)

If parking brake is off, stop immediately and contact Toyota dealer.

(b)

(indicator and buzzer)

Fasten driver’s seat belt.

(c)

(indicator and buzzer)

Fasten front passenger’s seat belt.

(d)

Stop immediately and contact Toyota dealer.

(e)

Take vehicle to Toyota dealer.

(f)

Fill up tank.

(g)

Stop and check.

Service reminder indicators and warning buzzers

Summary of Contents for Corolla 2007








































































































































































































































































































Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands

Toyota Corolla 2007, Operating Manual

Search results

Summary of Contents for Corolla 2007

Reviews:

Related manuals for Corolla 2007

Brands by name

Popular brands