manualshive.com logo in svg

Town & Country Fireplaces D Series, Installation Manual

Share
Download
Town & Country Fireplaces D Series Installation Manual Download Page 54

 Rating Label 

100001140

DATE OF MANUFACTURE

Required components/ Éléments requis:  

 

Powervent Kit/ kit de ventilation mécanique TCVT.PV7.110 (on max.), TCVT.PVCV, TCVT.PVVT (on max.) 

Blower electrical rating:  

115v, 60hz, 1.1 A / Normes electriques du ventilateur:  115v, 60hz, 1.1 A

This appliance equipped for altitudes 0 - 4500 ft. (0 - 1372 m) / Cet unité est conçu pour des altitudes variant entre 0 - 4500 pieds (0 - 1372 m). In Canada, also 

must be installed in accordance with local codes, if any; if none, follow the current CAN/CGA-B149 (Canada), or ANSI Z223.1 (USA) Installation Codes. Installer 
l’appareil selon les codes ou règlements locaux, ou, en l’absence de tels règlements, selon les codes d’installation CAN/CGA-B149 (Canada), or ANSI Z223.1 
(USA) en vigeur.

MANUFACTURED (MOBILE) HOME:  This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, 
permanently located, manufactured (mobile) home where not prohibited by local codes. See owners manual for details. 
FABRIQUEZ (MOBILE) MAISON:  Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique et peut être installé dans une 
maison préfabriquée (mobile) installée à demeure si les règlements locaux le permettent. Voir la notice du propriétaire pour plus de détails. Cet appareil ne peut 

Install in accordance with the current standard Mobile Homes,CAN/CSA Z240 MH (in CANADA), and the Manufacturer’s Home Construction and Safety Standard, 
Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, (in 
the U.S.A.).  Cet appareil diot être installé conformemént aux exigences de la norme CAN/CSA Z240 MH en vigueur de l’ACNOR, Installations de gaz dans les 
Constructions Mobiles.
FOR USE WITH THE GLASS AND SCREEN BARRIER CERTIFIED WITH THE APPLIANCE ONLY / POUR UTILISATION UNIQUEMENT AVEC LES PORTES IN VERRE 
CERTIFIÉES AVEC L’APPAREIL

 

 

MINIMUM CLEARANCES TO COMBUSTIBLES / CLAIRANCES MINIMALES AVEC LES COMBUSTIBLE

 

Left and Right side are determined when facing the front of the appliance. / Les côtés droit et gauche se déterminent  
en se mettant devant l’appareil et en lui faisant face.

 

Top, Back and Side Standoffs / Sommet, Arrière et Côté Butée 

 

0 in./ 0 po. 

(0 mm)

 

Sidewall to Appliance / Du mur latéral a l’appareil 

 

 

4 in./ 4 po. 

(102 mm)

 

Ceiling to Appliance / Plafond a l’appareil 

 

 

24 in./ 24 po. 

(610 mm)

 

Mantel to Appliance / Du manteau al’appareil 

 

 

*9 in./ 9 po. 

(229 mm)

 

Maximum Mantel Extension / Allongement maximum du manteau 

 

*12 in./ 12 po. 

(305 mm)

 

      *See Installation Manual for more detail / Voyez des Directive 
      de l’Installation pour plus détaux.

 

Mantel Supports / Supports du manteau 

 

 

4 in./ 4 po. 

(102 mm)

 

Vent Pipe / Déchargez le Tuyau 

 

 

1.75 in./ 1.75 po. 

(45 mm)

 

Fireplace Products Ltd.

Duncan, British Columbia, 

Canada

MADE IN CANADA
FABRIQUE AU CANADA

160119 

100001674-50 

1-TCWS54STOK-D

 

WARNING:  Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer 

installer, service agency or the gas supplier.

des dommages matériels ou des blessures. Voir la notice de l’utilisateur qui accompgne l’appareil. Pour de l’aide ou des 
renseignements supplémentaires, consultez un installateur, un technicien agréé ou le fournisseur de gaz.

FOR USE WITH/ 

 

NATURAL GAS/ 

LP GAS/

EN CASE D’EMPLOI AVEC:  

DU GAZ NATUREL  DU GAZ LP

Minimum supply pressure / Pression minimum d’alimentation: 

5.0 in/wc / 5.0 po/c.e. 

12.5 in/wc / 12.5 po/c.e.

(For the purpose of input adjustment / dans le but de régler l’alimenation)

 

     (1.25 kPa) 

      (3.11 kPa)

Maximum supply pressure / Pression maximum d’alimentation: 

13.9 in/wc / 13.9 po/c.e. 

13.9 in/wc / 13.9 po/c.e.

 

 

     (3.45 kPa) 

      (3.45 kPa)

Manifold pressure / Pression de la tuyauterie:      Maximum 

3.5 in/wc / 3.5 po/c.e. 

10.0 in/wc / 10.0 po/c.e.

 

 

     (0.87 kPa) 

      (2.49 kPa)

 

              NC x2 

 

            LC x2

Input BTU/hr (kW) / Entree BTU/h (kW): 

Max.:   54,900   (16.0) 

Max.:   54,900   (16.0)

 

 

Min.:    38,500   (11.3) 

Min.:    45,000   (13.2)

This Appliance is Equipped For Use With   /

Cet Appareil est Équipé Pour Utilise Avec :

NATURAL GAS
GAZ NATUREL

LP-GAS
LP GAZ

VENTED GAS FIREPLACE - NOT FOR USE WITH SOLID FUEL
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC DU 
COMBUSTIBLE SOLIDE

ANSI Z21.50-2016 / CSA 2.22-2016 Vented Gas Fireplaces
CAN/CGA 2.17-M91 Gas-Fired Appliance For Use At High Altitudes.

MODEL/
MODELE:

 

 

 

    

 

SERIES/      
SERIE:

      

TCWS54STOK

 

 

       

D

This is a decorative product and is not intended 
to be used as a heating appliance.

P.4.1-15 Efficiency: 30.7%

TM

54

TCWS54STOK_270619-56

Summary of Contents for D Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands