manualshive.com logo in svg

Town & Country Fireplaces D Series, Installation Manual

Share
Download
Town & Country Fireplaces D Series Installation Manual Download Page 22

100001140

For Power Venting this fireplace, “Power Venting Options” on page 17 and “Venting Configurations” on 
page 23.   

 

VENT SUPPORTS:  A minimum of 1 support every 4’ must be used.

CAUTION:  UNDER NO CONDITION SHOULD COMBUSTIBLE MATERIAL BE CLOSER THAN 1 ½ 
INCHES FROM ANY PART OF THE VENTING PIPE.

This installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas 
Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

All electrical installations should be performed by a qualified electrician to the Canadian and U.S. National 
Electrical Codes (CSA C22.1 for Canada), (ANSI/NFPA 70 for the U.S.) and/or local electrical codes.

     Under no circumstances shall a rheostat be used to alter the voltage supply to this unit.

MINIMUM VENTING CLEARANCES TO COMBUSTIBLE MATERIALS

Terminal casing:
 

0 in. (0 mm)

Vertical vent pipe:
 

1.5 in. (38 mm)

Horizontal vent pipe:
 

1.5 in. (38 mm)

All other clearances are as per the fireplace installation instructions.

22

TCWS54STOK_270619-56

 Venting - Wall Power Vent Kit Only 

Summary of Contents for D Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands