manualshive.com logo in svg

Town & Country Fireplaces D Series, Installation Manual

Share
Download
Town & Country Fireplaces D Series Installation Manual Download Page 2

 Table of Contents 

100001140

2

TCWS54STOK_270619-56

We recommend that our gas hearth products 
be installed and serviced by professionals who 
are certified in the United States by the National 
Fireplace Institute® (NFI) as NFI Gas Specialists

HOT GLASS WILL CAUSE 

BURNS.

DO NOT TOUCH GLASS UNTIL 

COOLED.

NEVER ALLOW CHILDREN TO 

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the 

hot viewing glass is provided with the appliance and 

shall be installed for the protection of children and 
other at-risk individuals.

WARNING: 

This product 

can expose you to chemicals 
including ceramic fibers, 
which are known to the State 

of California to cause cancer, and carbon 
monoxide, which is known to the State of 
California to cause birth defects or other 
reproductive harm.

For more information go to 
www.P65Warnings.ca.gov.

This warning is applicable to all 

Pacific Energy Fireplace Products

 R - Value Statement  .................................................................. 3
 Caution  ...................................................................................... 3
 Safety  ........................................................................................ 3
 Important Note for the Commonwealth of Massachusetts  ....... 4
 Fireplace Dimensions  ................................................................ 5
 Minimum Clearances to Combustible Material  ......................... 6
 Installation Requirements  .......................................................... 7
 Manufactured (Mobile) Home  .................................................... 7
 Door Frame Removal  ................................................................ 7
 Standoffs  ................................................................................... 8
 Locating The Fireplace  .............................................................. 8
 Framing and Finishing  ............................................................... 9
 Building envelope sealing procedure  ...................................... 10

Double sided tape for exterior side vapour barrier .......... 11

 Building materials - Outer trim profile view  ............................. 12

Non-combustible board detail ......................................... 14
Non-combustible recessed installation detail .................. 14
Calcium silicate board ...................................................... 14
Secure steel frame to combustible framing ..................... 15

 Adjustable Lintel  ...................................................................... 15

Lintel Adjustment ............................................................. 16

 Power Venting Options  ............................................................ 17
 Electrical  .................................................................................. 18

Installation ........................................................................ 18

 Wall Switch and Remote Control  ............................................ 19

Linking the remote control unit to the wall switch............ 19

 Selecting Natural Vent and Power Vent Modes ....................... 19
 Home Automation  ................................................................... 20

Home automation cable length  ....................................... 20

 Gas Supply  .............................................................................. 21
 Venting - Wall Power Vent Kit Only .......................................... 22

 Venting Configurations  ............................................................ 23
 Minimum Vent Length Chart  .................................................... 24
 Vent Terminal Minimum Clearances  ........................................ 24
 Venting Components  ............................................................... 25
 Vent Pipe Sealant  .................................................................... 26
 Optional Tranquility Burner  ...................................................... 27

Contents of Package: ....................................................... 27
Installation: ....................................................................... 28

 Propane Conversion  ................................................................ 33
 Optional Twilight Diamond Burner  ........................................... 35

Contents of Package: ....................................................... 35
Installation: ....................................................................... 36
Installation (Indoor side only) ........................................... 39

 Finishing Touch Trim Kit Installation  ........................................ 39
 Wiring instructions for the TC54ST Twilight Burner kit  ............ 41
 Gas Pressure Check  ................................................................ 43

Correct gas pressure requirement:................................... 43

 Burner Flame Adjustment  ........................................................ 44
 Firebox Panels Installation  ...................................................... 45
 Lighting Instructions  ................................................................ 46
 Maintenance  ............................................................................ 47

Glass Panel: ..................................................................... 47
Annual Inspection: ............................................................ 47
Periodically: ...................................................................... 47

 Replacement parts-TCWS.54STOK  ........................................ 48
 Replacement Parts - TCWS.54DST  ........................................ 49
 Replacement Parts - Tranquility Burner  .................................. 50
 Replacement Parts - Twilight Diamond Burner  ....................... 51
 Replacement Parts – Valve Control System  ............................ 52
 Wiring Diagram  ........................................................................ 53
 Rating Label  ............................................................................ 54

Summary of Contents for D Series

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands