Town & Country Fireplaces D Series Installation Manual Download Page 1 | Manualshive

Page: 1 / 56

Town & Country Fireplaces D Series Installation Manual Download Page 1

WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property damage,
personal injury or death.

FOR YOUR SAFETY

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch.
•  Do not use any phone in your building.
•  Immediately call your gas supplier from a

neighbour’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier call the

fire department.

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

This appliance may be installed in an aftermarket
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.

This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a
certified kit is used.

This appliance is suitable for installation in a
bedroom or bed sitting room.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Visit www.townandcountryfireplaces.com for the most recent version of this manual

TCWS.54STOK

Indoor/outdoor Fireplace

Installation Manual.

270619-56

TCWS54.STOK

100001140-50

This is a decorative product
and is not intended to be
used as a heating appliance.

INSTALLATION MANUAL

MODEL: TCWS.54STOK
SERIES D
DIRECT VENTED
DECORATIVE GAS
SEE THRU APPLIANCE

POWER VENTED ONLY

1
2
3
...
»

Summary of Contents for D Series

























































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands