Toshiba TXZ SERIES Reference Manual Download Page 29 | Manualshive

Page: 29 / 67

background image

TXZ Family

Serial Peripheral Interface

2019-02-28

29 / 67

Rev. 3.0

3.3.2.2. SIO mode

When write "1" to

[TSPIxCR1]

<TSPIMS>(Communication mode selection), the TSPI operates in SIO mode.

In SIO mode, one master device can be connected with one slave device via TSPIxSCK(clock input/output),
TSPIxTXD(data transmission), TSPIxRXD(data reception).

● Master

operation

The TSPI outputs a clock from TSPIxSCK and operates synchronously with TSPIxSCK.

● Slave

operation

The TSPI receives a clock from TSPIxSCK and operates synchronously with TSPIxSCK.

Note: When using SIO mode, do not select TSPIxCS0/1/2/3 and TSPIxCSIN in port setting.

3.3.2.3. Master / Slave selection

The TSPI operates as Master (the device outputs transfer clock) or Slave (transfer clock is input to the device).

When "0" is set to

[TSPIxCR1]

<MSTR>, the TSPI operates as Slave.

When "1" is set to

[TSPIxCR1]

<MSTR>, the TSPI operates as Master.

3.3.3. Buffer Structure

The transmit buffer and receive buffer are independent respectively. Each buffer has a double-buffering structure
consisting of the FIFO and 32-bit width shift register.

There are the transmit FIFO and receive FIFO. Each FIFO is 16-bit width and 8-stage. Settable FIFO level varies
depending on the data length.

Table 3.2 Data format and settable fill level

Data

Settable fill level

Transmit FIFO

[TSPIxCR2]<TIL[3:0]>

Receive FIFO

[TSPIxCR2]<RIL[3:0]>

7 to 16bit

0 to 7

1 to 8

17 to 32bit

0 to 3

1 to 4

Note: Set a value within the settable fill level. If a value outside of the settable fill level is set, the operation is

not guaranteed.

«
...
27
28
29
30
31
...
»

Summary of Contents for TXZ SERIES




































































Reviews:

No comments

Related manuals for TXZ SERIES

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 20

Brand: ZKTeco Pages: 11

Brand: IBM Pages: 214

Brand: NXP Semiconductors Pages: 20

Brand: U-Tron Pages: 8

Brand: zeeltronic Pages: 13

Brand: QD Dynamics Pages: 64

Brand: Lumel Pages: 32

Brand: Hoffer Pages: 57

MotorController WCC 310

Brand: Window Master Pages: 19

LS-RGB-DMX CONTROL

Brand: JBSYSTEMS Light Pages: 12

Brand: Gardenic Pages: 14

Brand: W.E.ST. Pages: 34

Brand: Arbor Technology Pages: 79

Brand: Ledj Pages: 12

Brand: Belimo Pages: 2

Brand: Danfoss Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands