manualshive.com logo in svg

Toshiba TLCS-870/C1 Series, Manual

The Toshiba TLCS-870/C1 Series user manual is available for free download on manualshive.com. This comprehensive manual provides step-by-step instructions and valuable information on operating and maintaining the TLCS-870/C1 Series. Get your free manual now and unlock the full potential of this exceptional Toshiba product.

Share
Download
background image

Page 246

 17. Synchronous Serial Interface (SIO)

 17.5 Transfer Modes

 TMP89FM42

RA001

(1)

When the internal clock is used and SIO0SR<TBFL> is "0"

When the data transmission is completed, the SCLK0 pin becomes the initial state and the SO0 pin

becomes the "H" level. SIO0SR<SEF> remains at "0". When the internal clock is used, the serial
clock and data output is stopped until the next transmit data is written into SIO0BUF (automatic
wait).

When the subsequent data is written into SIO0BUF, SIO0SR<SEF> is set to "1", the SCLK0 pin

outputs the serial clock, and the transmit operation is restarted. An INTSIO0 interrupt request is gen-
erated at the restart of the transmit operation.

(2)

When an external clock is used and SIO0SR<TBFL> is "0"

When the data transmission is completed, the SO pin keeps last output value. When an external

serial clock is input to the SCLK0 pin after completion of the data transmission, an undefined value
is transmitted and the transmit underrun error flag SIO0SR<UERR> is set to "1".

If a transmit underrun error occurs, data must not be written to SIO0BUF during the transmission

of an undefined value. (It is recommended to finish the transmit operation by setting
SIO0CR<SIOS> to "0" or force the transmit operation to stop by setting SIO0CR<SIOM> to "00".)

The transmit underrun error flag SIO0SR<UERR> is cleared by reading SIO0SR.

(3)

When an internal or external clock is used and SIO0SR<TBFL> is "1"

When the data transmission is completed, SIO0SR<TBFL> is cleared to "0". The data in

SIO0BUF is transferred to the shift register and the transmission of subsequent data is started. At this
time, SIO0SR<SEF> is set to "1" and an INTSIO0 interrupt request is generated.

 17.5.1.5 Stopping the transmit operation

Set SIO0CR<SIOS> to "0" to stop the transmit operation. When SIO0SR<SEF> is "0", or when the

shift operation is not in progress, the transmit operation is stopped immediately and an INTSIO0 interrupt
request is generated. When SIO0SR<SEF> is "1", the transmit operation is stopped after all the data in the
shift register is transmitted (reserved stop). At this time, an INTSIO0 interrupt request is generated again.

When the transmit operation is completed, SIO0SR<SIOF, SEF and TBFL> are cleared to "0". Other

SIO0SR registers keep their values.

If the internal clock has been used, the SO0 pin automatically returns to the "H" level. If an external

clock has been used, the SO0 pin keeps the last output value. To return the SO0 pin to the "H" level, write
"00" to SIO0CR<SIOM> when the operation is stopped.

The transmit operation can be forced to stop by setting SIO0CR<SIOM> to "00" during the operation.

By setting SIO0CR<SIOM> to "00", SIO0CR<SIOS> and SIO0SR are cleared to "0" and the SIO stops
the operation, regardless of the SIO0SR<SEF> value. The SO0 pin becomes the "H" level. If the internal
clock is selected, the SCLK0 pin returns to the initial level.

Summary of Contents for TLCS-870/C1 Series

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TLCS-870/C1 Series

Hafele DT 100 Operating Instructions Manual preview
DT 100
Brand: Hafele Pages: 82
Bard ECU Series Advanced Programming & Features preview
ECU Series
Brand: Bard Pages: 8
Federal Signal Corporation FC Description, Specifications, Installation, Operation, And Service Manual preview
FC
Brand: Federal Signal Corporation Pages: 34
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Brand: Federal Signal Corporation Pages: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Brand: Federal Signal Corporation Pages: 32
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Brand: M-Audio Pages: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Brand: M Climate Pages: 12
National Instruments 73 Series Getting Started preview
73 Series
Brand: National Instruments Pages: 34
B&G ZEUS S Detailed App Manual preview
ZEUS S
Brand: B&G Pages: 19
PENKO 1020 CAN-RS232-RS422 MFL Manual preview
1020 CAN-RS232-RS422 MFL
Brand: PENKO Pages: 29
Netro SPRITE Quick Start Manual preview
SPRITE
Brand: Netro Pages: 14
Gecko MC-MP Service Manual preview
MC-MP
Brand: Gecko Pages: 82
S.E.A. Group Sundstrom SR307 Manual preview
Sundstrom SR307
Brand: S.E.A. Group Pages: 5
Beckhoff CX8080 Documentation preview
CX8080
Brand: Beckhoff Pages: 67
Omron K8AK-LS Manual preview
K8AK-LS
Brand: Omron Pages: 12
Siro 40567 Instruction Manual preview
40567
Brand: Siro Pages: 2
SLV 470700 Operating Manual preview
470700
Brand: SLV Pages: 11
POLA HD38 Handbook preview
HD38
Brand: POLA Pages: 7

Brands by name

Popular brands

Load more brands