manualshive.com logo in svg

Toshiba TLCS-870/C1 Series, Manual

The Toshiba TLCS-870/C1 Series user manual is available for free download on manualshive.com. This comprehensive manual provides step-by-step instructions and valuable information on operating and maintaining the TLCS-870/C1 Series. Get your free manual now and unlock the full potential of this exceptional Toshiba product.

Share
Download
background image

Page 160

 13. 16-bit Timer Counter (TCA)

 13.4 Timer Function

 TMP89FM42

RA001

 13.4.6 Programmable pulse generate (PPG) mode

In the PPG output mode, an arbitrary duty pulse is output by two timer registers.

 13.4.6.1 Setting

Setting the operation mode selection TA0MOD<TA0M> to "011"  activates the PPG output mode.

Select the source clock at TA0MOD<TA0CK>. Select continuous or one-shot PPG output at
TA0CR<TA0MPPG>.

Set the PPG output cycle at TA0DRA and set the time until the output is reversed first at TA0DRB. Be

sure to set register values so that TA0DRA is larger than TA0DRB.

Note that this mode uses  the 

PPGA0

 pin.  the 

PPGA0

 pin must be set to the output mode beforehand in

port settings.

Set the initial state of the 

PPGA0

 pin at the timer flip-flop TA0CR<TA0TFF>. Setting

TA0CR<TA0TFF> to "1" selects the "H" level as the initial state of the 

PPGA0

 pin. Setting

TA0CR<TA0TFF> to "0" selects the "L" level as the initial state of the 

PPGA0

 pin.

The operation is started by setting TA0CR<TA0S> to "1". After the timer is started, writing to

TA0MOD and TA0CR<TA0OVE, TA0TFF> is disabled. Be sure to complete the required mode settings
before starting the timer.

 13.4.6.2 Operation

 after the timer is started, the up counter increments .

When a match between the up counter value and the value set to timer register B (TA0DRB) is detected,

the 

PPGA0

 pin is changed to the "H" level if TA0CR<TA0TFF> is "0", or the 

PPGA0

 pin is changed to the

"L" level if TA0CR<TA0TFF> is "1".

Subsequently, the up counter continues counting. When a match between the up counter value and the

value set to timer register A (TA0DRA) is detected, the 

PPGA0

 pin is changed to the "L" level if

TA0CR<TA0TEFF> is "0", or the 

PPGA0

 pin is changed to the "H" level if TA0CR<TA0TFF> is "1". At

this time, an INTTA0 interrupt request occurs. If the PPG output control TA0CR<TA0MPPG> is set to
"1" (one-shot), TA0CR<TA0S> is automatically cleared to "0" and the timer stops.

If TA0CR<TA0MPPG> is set to "0" (continuous), the up counter is cleared to "0000H" and continues

counting and PPG output. When TA0CR<TA0S> is set to "0" (including the auto stop by the one-shot
operation) during the PPG output, the 

PPGA0

 pin returns to the level set in TA0CR<TA0TFF>.

TA0CR<TA0MPPG> can be changed during the operation. Changing TA0CR<TA0MPPG> from "1" to

"0" during the operation cancels the one-shot operation and enables the continuous operation. Changing
TA0CR<TA0MPPG> from "0" to "1" during the operation clears TA0CR<TA0S> to "0" and stops the
timer automatically after the current pulse output is completed.

Timer registers A and B can be set to the double buffer. Setting TA0CR<TA0DBF> to "1" enables the

double buffer. When the values set to TA0DRA and TA0DRB are changed during the PPG output with the
double buffer enabled, the writing to TA0DRA and TA0DRB will not immediately become effective but
will become effective when a match between TA0DRA and the up counter is detected. If the double buffer
is disabled, the writing to TA0DRA and TA0DRB will become effective immediately. If the written value
is smaller than the up counter value, the up counter overflows. After a cycle, the counter match process is
executed to reverse the output.

Summary of Contents for TLCS-870/C1 Series

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TLCS-870/C1 Series

Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Brand: fadini Pages: 28
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Brand: Mitsubishi Pages: 30
Xylem Aquavar IPC Quick Start Manual preview
Aquavar IPC
Brand: Xylem Pages: 28
Overland Storage NEO 2000e Remove & Replace Instructions preview
NEO 2000e
Brand: Overland Storage Pages: 4
VDH ALFANET 1-LS User Manual preview
ALFANET 1-LS
Brand: VDH Pages: 4
VIRDI AC-2200 User Manual preview
AC-2200
Brand: VIRDI Pages: 73
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Brand: Teradek Pages: 10
Renishaw PHC10-3 PLUS Installation Manual preview
PHC10-3 PLUS
Brand: Renishaw Pages: 68
Hanbay MC DC-2.00 Series User Manual preview
MC DC-2.00 Series
Brand: Hanbay Pages: 7
Edge-Core EWS5203 Regulatory Information preview
EWS5203
Brand: Edge-Core Pages: 8
Advantech LNC-5800D Hardware Maintenance Manual preview
LNC-5800D
Brand: Advantech Pages: 46
Lattice Semiconductor MachXO5T-NX Quick Start preview
MachXO5T-NX
Brand: Lattice Semiconductor Pages: 2
DAB SMART PRESS WG 1,5HP User Manual Instructions For Installation And Maintenance preview
SMART PRESS WG 1,5HP
Brand: DAB Pages: 20
Eldat TRS06-01 Mounting And Operating Manual preview
TRS06-01
Brand: Eldat Pages: 15
Resol DeltaSol C2 Manual preview
DeltaSol C2
Brand: Resol Pages: 20
IBM ThinkPad 130 Introduction Manual preview
ThinkPad 130
Brand: IBM Pages: 104

Brands by name

Popular brands

Load more brands