Toshiba SD-2300 Service Manual Download Page 94

Page: 94 / 160

1-3-2. Loading Belt

1. Remove the gear (1) by releasing the claw.

2. Remove the gear (2).

3. Remove the gear (3) and the loading belt (4).

4. Replace the loading belt (4) with a new one.

5. When mounting, perform the reverse order of the

removal.

Note:

• When mounting the loading belt (4), twisting and

attaching of a grease, etc. are not allowed.

Fig. 2-1-15

Gear (1)

Gear (2)

Gear (3)

Claw

Mechanism
chassis assembly

Loading belt (4)

1-3-3. Loading Motor

1. Remove the loading belt. (Refer to item 1-3-2.)

2. Remove two screws (1) and two claws. Then remove

the loading motor (2) (with the loading motor PC

board (3) attached).

3. Desolder the terminal section of the loading motor (2)

and remove the loading motor PC board (3).

4. Replace the loading motor (2) with a new one.

5. When mounting, perform the reverse order of the

removal.

Note:

• When replacing the loading motor, meet the polarity

phase of the terminals. (Mount the motor with the

label positioned as shown in Fig. 2-1-16.)

Fig. 2-1-16

Claw

Loading motor (2)

Loading motor
PC board (3)

Claw

Motor label
side

Mechanism
chassis assembly

Desolder

Screws (1)

Summary of Contents for SD-2300

































































































































































Search results

Summary of Contents for SD-2300

Reviews:

Related manuals for SD-2300

Brands by name

Popular brands

Toshiba SD-2300, Service Manual

Search results

Summary of Contents for SD-2300

Reviews:

Related manuals for SD-2300

Brands by name

Popular brands