Toshiba Satellite R830 Maintenance Manual Download Page 238 | Manualshive

Page: 238 / 515

background image

Tests and Diagnostics

PORTEGE R830 Satellite R830 Series Maintenance Manual (960-880)

[CONFIDENTIAL] 3-129

3.34.6.6 WIRED LAN Test

1) Test content
This test checks that normal communication can be performed with the built-in LAN card.
To execute the test, it is necessary that Mac address for the LAN card should have been set
and IP address should have been given to the machine.

■

Simple Mode

transmit 32 packet sizes data via the LAN line and confirm that a response can be received
normally.

■

Detail Mode

transmit 198 packet sizes data via the LAN line and confirm that a response can be received
normally.

2) Test Screen

▼

LAN Card information: Displays the name of LAN card, MAC address and IP address.

▼

Progress status: Displays the progress status of the test with the progress bar.

3) Result Decision

■

In the case of PASS

The PASS Count display on the test screen is zoomed in and (OK) is displayed in the Result
field on the WinPE T&D screen.

«
...
236
237
238
239
240
...
»

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite R830

AcerNote Light 370P

Brand: Acer Pages: 16

ThinkPad G40 Series

Brand: IBM Pages: 8

Brand: IBM Pages: 9

ThinkPad G40 Series

Brand: IBM Pages: 114

Brand: IBM Pages: 235

Brand: IBM Pages: 18

Brand: IBM Pages: 27

Brand: IBM Pages: 2

Brand: IBM Pages: 143

Brand: XPG Pages: 46

Brand: Medion Pages: 306

Brand: Fujitsu Pages: 32

Brand: Lenovo Pages: 86

- G550 2958 NoteBook PC

Brand: Lenovo Pages: 128

PCG-Z1RA Marketing Specifications Sheet

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

PCG-VX89 VAIO User Guide (primary manual)

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands