Toshiba Satellite R830 Maintenance Manual Download Page 18 | Manualshive

Page: 18 / 515

background image

1 Hardware Overview

1-8 [CONFIDENTIAL]

PORTEGE R830 Satellite R830

Series Maintenance Manual (960-880)



eSATA/USB combo

One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on
the left hand side of the computer. This port has eSATA (External Serial ATA) function.
Some models are equipped with an eSATA/USB combo port.
A Charge power supply (When a computer is power-on or sleep).



External monitor (RGB) port

This port provides 15-pin, analog VGA port. This port allows you to connect an external
monitor to the computer.



HDMI out port

HDMI out port can connect with Type A connector HDMI cable. HDMI cable can send
video and audio signals.



SD Media slot

This slot lets you insert an SD™/SDHC™ memory card, miniSD™/microSD™ Card,
and MultiMediaCard



ExpressCard slot(Some models)

This slot allows you to install a single ExpressCard device.



PC Card slot(Some models)

This slot allows you to install a single PC Card device.



Smart Card slot(Some models)

This slot allows you to install a smart card device.
Some models are equipped with a Smart Card slot.



Fingerprint sensor(Some models)

The computer is equipped with a fingerprint sensor and fingerprint authentication utility.
They enable only person who has registered his/her fingerprint to use the computer.

«
...
16
17
18
19
20
...
»

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite R830

Brand: Gateway Pages: 7

Brand: Digitus Pages: 9

Brand: J-PRO Pages: 50

Barbie B-Bright

Brand: Oregon Scientific Pages: 16

Brand: Lenovo Pages: 84

3i-15 Chromebook

Brand: Lenovo Pages: 42

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 108

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 6

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 112

Brand: Lenovo Pages: 132

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands