manualshive.com logo in svg

Toshiba Satellite R830, Maintenance Manual

The Toshiba Satellite R830 is a high-performance laptop designed for professionals on the go. To ensure your device remains in optimal condition, download the Maintenance Manual for free from manualshive.com today. This comprehensive manual provides step-by-step instructions and valuable insights to help you maintain your Toshiba Satellite R830 effortlessly.

Share
Download
background image

4.11  3G card 

4 Replacement Procedures 

PORTÉGÉ R830/Satellite R830 Maintenance Manual (960-880) 

[CONFIDENTIAL] 

4-37 

Installing the 3G card 

To install the 3G card, follow the steps below and refer to Figure 4-17 to 4-22. 

1.

 

Insert the 

3G card

 to the connector on the 3G board slantwise and press it to connect 

firmly. 

2.

 

Secure the 

3G card

 with the following 

screws

. 

•

 

M2

×

3B 

 

S-THIN HEAD screw  

 

 

×

2 

3.

 

Connect the 

3G antenna cables

 to the connectors on the 3G card. 

4.

 

Turn over the 3G board. (In models with 3G board and ExpressCard/Smart Card 

only) 

5.

 

Set the 3G board to the cover assembly.  

6.

 

Connect the 

3G board FPC

 to the connector 

CN9720

 on the 3G board. 

7.

 

Secure the 3G board with the following 

screws

. 

•

 

M2

×

4C 

 

S-THIN HEAD screw  

 

 

×

3 

8.

 

Arrange the 

3G antenna cables

 in place. 

9.

 

Connect the 

sound board FPC

 to the connector 

CN9670

 on the sound board and 

CN9570

 on the system board and stick the 

acetate tape

 in place. 

10.

 

Connect the 

USB 3.0 FPC

 to the connector 

CN9671

 on the sound board and 

CN9571

 

on the system board. (USB 3.0 model only) 

CAUTION:  When replacing the USB 3.0 FPC with a new one, use the USB 3.0 FPC on 

which “AL-S” is printed. Do not use the parts for 

PORTÉGÉ R700.

 

 

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite R830

NEC VERSA VX Service And Reference Manual preview
VERSA VX
Brand: NEC Pages: 106
NEC VERSA VX Release Note preview
VERSA VX
Brand: NEC Pages: 10
NEC VERSA SXI Release Note preview
VERSA SXI
Brand: NEC Pages: 8
NEC VERSA SXI Using preview
VERSA SXI
Brand: NEC Pages: 2
NEC VERSA DAYLITE Release Note preview
VERSA DAYLITE
Brand: NEC Pages: 4
Samsung NP600B4C User Manual preview
NP600B4C
Brand: Samsung Pages: 143
Samsung NP550P5C User Manual preview
NP550P5C
Brand: Samsung Pages: 122
Gateway 450ROG Replacement Instructions Manual preview
450ROG
Brand: Gateway Pages: 12
UMAX Technologies visionbook 12WRx User Manual preview
visionbook 12WRx
Brand: UMAX Technologies Pages: 72
Lenovo 2516AEU Brochure preview
2516AEU
Brand: Lenovo Pages: 4
Asus CA16767 User Manual preview
CA16767
Brand: Asus Pages: 28
Asus C202SA Disassembly Manual preview
C202SA
Brand: Asus Pages: 23
Asus Disney Netpal MK90H User Manual preview
Disney Netpal MK90H
Brand: Asus Pages: 68
Asus CA14675 User Manual preview
CA14675
Brand: Asus Pages: 20
Asus BX31LA E-Manual preview
BX31LA
Brand: Asus Pages: 112
Asus BQ0388R Manual preview
BQ0388R
Brand: Asus Pages: 96
Asus BX51V E-Manual preview
BX51V
Brand: Asus Pages: 104
Asus C213NA-BW0034-OSS E-Manual preview
C213NA-BW0034-OSS
Brand: Asus Pages: 98

Brands by name

Popular brands

Load more brands