Toshiba Satellite R830 Maintenance Manual Download Page 193

Page: 193 / 515

Tests and Diagnostics

3-84 [CONFIDENTIAL])

PORTEGE R830 Satellite R830 Series Maintenance Manual (960-880)

Subtest02 (GbE)

This subtest checks the operation of mini-PCI I/F by the loopback test in the
chip. Select

to execute and press

Enter

The following message will appear:

Testing adaptor...hit <ESC> to abort.
*

External Loopback Test...PASSED
Testing completed.
*

Loopback Test Complete
*

1000Base Auto-negotiation TxRx Test

* CE Test Complete

NOTE: The menu displayed by your computer may be slightly different from the one

shown above.

defective

found,

message will appear in the display.

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands

Toshiba Satellite R830, Maintenance Manual

Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands