Toshiba Satellite R830 Maintenance Manual Download Page 27

Page: 27 / 515

1 Hardware Overview

PORTEGE R830 Satellite R830

Series Maintenance Manual (960-880)

[CONFIDENTIAL]

1-17



Clock generator

：

ICS9LVRS394CKLFT

(Made by Integrated Device Technology)



EC/KBC

：

MEC1609-PZP(REVISION.D) (Made by standard micro system)



GPIO Expander

：

ECE1088-DZK (Made by standard micro system)



PSC: TMP86FS49BUG (made by Toshiba)



TPM: SLB9635 TT 1.2FW3.17 (made by Infineon)



Sensor



Temperature reset IC

：

105-degree-C type



Thermistor

：

Four places (CPU, Memory, for normal temperature measurement, 3G)



Magneto metric sensor

：

Use it as a LCD opening-and-closing sensor (ferrite magneto system).



Acceleration sensor

：

Made by ST Microelectronics

TSH35TR (Three axes)
HDD protection



Fingerprint sensor

：

Made by Authen Tec.

It mounts between the Touchpad buttons.

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands

Toshiba Satellite R830, Maintenance Manual

Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands