Toshiba Satellite R830 Maintenance Manual Download Page 16

Page: 16 / 515

1 Hardware Overview

1-6 [CONFIDENTIAL]

PORTEGE R830 Satellite R830

Series Maintenance Manual (960-880)



Chipset

Toshiba PORTEGE R830 Satellite R830

Series

computer is Equipped with Intel Cougar

Point QM67 (AMT model) or HM65 (Non-AMT model).



VGA Controller

The PC comes in with one of the following types:



The internal graphics controller in Intel Processor (Core i*) is used.



HDD

The computer has a 2.5-inch SATA HDD. The following capacities are available.



250GB/320/500/640 GB



SSD

Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive.

2.5"SATA SSD type



256GB/512GB

1.8"SATA SSD type



128GB



USB FDD

A 3.5-inch USB FDD accommodates 2HD (1.44MB) or 2DD (720KB) disks.



Optical Drive

A DVD Super Multi drive (double layer) can be installed.
They are 7mm thickness or 9.5mm thickness by a model.

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands

Toshiba Satellite R830, Maintenance Manual

Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands