Toshiba Satellite R830 Maintenance Manual Download Page 161 | Manualshive

Page: 161 / 515

background image

Tests and Diagnostics

3-52 [CONFIDENTIAL])

PORTEGE R830 Satellite R830 Series Maintenance Manual (960-880)

[Touch Pad On/OFF Button test]

Press [Touch Pad On/OFF] Button

Please press Touch Pad On/OFF button

After checking Touch, return to the ONLY ONE TEST menu automatically.

Subtest 04

USB port select menu

NOTE: When executing this subtest, USB test module and USB cable must be

connected.

This subtest checks if USB port works properly.

The following menu appears in the display.

######## USB Port Select (XXXXXXXXX)

########

#################################################################
*

*

*

0 ............ Port 0

(Front in the right side)

*

*

1 ............ Port 1

(Behind the right side)

*

*

2 ............ Port 2

(Left side)

*

*

9

............

EXIT

*

*

*

*****************************************************************
.... Press test number [0-2, 9] ?

Connect the USB test module and USB cable to the computer.

Input the port test number and press

Enter

.

OK message appears in the display if the test ends without a defective.

NG message appears in the display if a defective is found during the test.
Confirm the connection of cable, then execute the test again.

Press

9

and return to ONLY ONE TESST menu.

«
...
159
160
161
162
163
...
»

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Satellite R830

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 56

Toughbook CF-18 Series

Brand: Panasonic Pages: 48

Brand: XMG Pages: 23

Brand: EVGA Pages: 15

Brand: EUROCOM Pages: 96

Brand: chiliGREEN Pages: 43

Brand: Packard Bell Pages: 56

HOT WHEELS ACCELERATOR

Brand: Oregon Scientific Pages: 28

Toughbook CF-72TCJUZPM

Brand: Panasonic Pages: 36

Brand: Fujitsu Pages: 8

Brand: Fujitsu Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands