Toshiba Satellite R830 Maintenance Manual Download Page 25

Page: 25 / 515

1 Hardware Overview

PORTEGE R830 Satellite R830

Series Maintenance Manual (960-880)

[CONFIDENTIAL]

1-15



Chipset

(1)HM65 (Non-AMT)

(2)QM67 (AMT)

・

989-ball 25×25mm FCBGA Package



VGA Controller

The PC comes in with one of the following types:



The internal graphics controller in Intel Processor (Core i*) is used..



LAN Controller

This controller has the following functions:



Support only a Gigabit Ethernet.



RJ45x1 port (with LED), docking connector (branch) 1 port.



WOL support (from S3, S4, and S5)



LAN controller

Made in

Intel Lewisville (WG82579V/LM(AMT))

: PCI-Ex Connection



AMT6.0 support (BTO correspondence)



Wireless LAN



One PCI Express Mini Card slot1

Atheros 802.11(b/g)13ch-HB195 MOW-HMC

Atheros 802.11(a/g/n)13ch-HB116 MOW-HMC

Atheros 802.11(b/g/n)13ch-HB125 MOW-HMC

Atheros 802.11(b/g/n)WB195-HMC w/ BT V3.0+HS

Atheros 802.11(b/g)WB195-HMC w/ BT V3.0+HS

Intel 802.11(b/g/n)13ch-CP 1x2 MOW-HMC

Intel a/b/n(2x2) RP2 MOW-HMC w/ BT V3.0+EDR

Intel a/g/n(2x2) TP MOW-HMC

Intel 802.16e(a/g/n)13ch+WiMAX-KP 2x2 MOW-HMC(BestBuy)

Intel 802.16e(b/g/n)WiMAX KelseyPeak



WOWL support (only Intel module)

Summary of Contents for Satellite R830




































































































































































































































































































































































































































































































































Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands

Toshiba Satellite R830, Maintenance Manual

Search results

Summary of Contents for Satellite R830

Reviews:

Related manuals for Satellite R830

Brands by name

Popular brands