Toshiba IP edge EC Installation Manual Download Page 75

Page: 75 / 206

ADD MEMBER NODE

MEETING IP Address Change Procedure

Installation Manual August, 2011

4-19

Repeat this process for each Member Node.

ADD MEMBER NODE

The following process adds then, attaches the member nodes to the
primary node. IP

edge

EC and EM servers can be a primary node.

Select

Administration

Enterprise

Servers

. The first time you

enter this screen the Server Name list will be empty.

Click on the

Add

icon.

Enter the Server Name, IP Address and Community Name of the
member node to be added.

Click on

Detect Server Information

. The System Type, Version and

Mac Address information will be displayed.

Enter location and any other useful information into the Description
box.

Click on the

Save

icon.

Click on the

Search

icon to display the server list.

ATTACH MEMBER NODE

This procedure attaches the member nodes. Part of the attach process is
the database synchronization from member to primary node.

If the server list is not displayed select

Administration

Enterprise

Servers

Click to check-mark the member server to attach.

Click on the

Attach

icon.

Summary of Contents for IP edge EC















































































































































































































Search results

Summary of Contents for IP edge EC

Reviews:

Related manuals for IP edge EC

Brands by name

Popular brands

Toshiba IP edge EC, Installation Manual

Search results

Summary of Contents for IP edge EC

Reviews:

Related manuals for IP edge EC

Brands by name

Popular brands