Toshiba GRL150-100 Series, Instruction Manual

Page: 251 / 267

⎯
250
⎯
6 F 2 S 0 8 2 8
List of Information
IEC103 Configurator Default setting
INF Description Contents
GI Type COT FUN DPI
ID Signal No. OFF ON
Standard Information numbers in monitor direction
System Function
0 End of General Interrogation Transmission completion of GI items. -- 8 10 255 -- -- --
0 Time Synchronization Time Synchronization ACK. -- 6 8 255 -- -- --
2 Reset FCB Reset FCB(toggle bit) ACK -- 5 3 192 -- -- --
3 Reset CU Reset CU ACK -- 5 4 192 -- -- --
4 Start/Restart Relay start/restart -- 5 5 192 -- -- --
5 Power On Relay power on. Not supported -- -- --
Status Indications
16 Auto-recloser active
If it is possible to use auto-recloser, this item is set
active, if impossible, inactive.
Not supported
17 Teleprotection active
If protection using telecommunication is available,
this item is set to active. If not, set to inactive.
GI 1 1, 9, 12 192 722 1 2
18 Protection active
If the protection is available, this item is set to
active. If not, set to inactive.
GI 1 1, 9, 12 192 723 1 2
19 LED reset Reset of latched LEDs -- 1 1, 11, 12 192 1418 -- 2
20 Monitor direction blocked
Block the 103 transmission from a relay to control
system. IECBLK: "Blocked" settimg.
GI 1 9, 11 192 1040 1 2
21 Test mode
Transmission of testmode situation froma relay to
control system. IECTST "ON" setting.
GI 1 9, 11 192 1039 1 2
22 Local parameter Setting
When a setting change has done at the local, the
event is sent to control system.
Not supported
23 Characteristic1 Setting group 1 active GI 1 1, 9, 11, 12 192 1024 1 2
24 Characteristic2 Setting group 2 active GI 1 1, 9, 11, 12 192 125 1 2
25 Characteristic3 Setting group 3 active GI 1 1, 9, 11, 12 192 1026 1 2
26 Characteristic4 Setting group 4 active GI 1 1, 9, 11, 12 192 1027 1 2
27 Auxiliary input1 Binary input 1 No set
28 Auxiliary input2 Binary input 2 No set
29 Auxiliary input3 Binary input 3 No set
30 Auxiliary input4 Binary input 4 No set
Supervision Indications
32 Measurand supervision I Zero sequence current supervision GI 1 1, 9 192 1356 1 2
33 Measurand supervision V Zero sequence voltage supervision Not supported
35 Phase sequence supervision Negative sequence voltage supevision Not supported
36 Trip circuit supervision Output circuit supervision GI 1 1, 9 192 1359 1 2
37 I>>backup operation Not supported
38 VT fuse failure VT failure Not supported
39 Teleprotection disturbed CF(Communication system Fail) supervision GI 1 1, 9 192 439 1 2
46 Group warning Only alarming GI 1 1, 9 192 1346 1 2
47 Group alarm Trip blocking and alarming GI 1 1, 9 192 1343 1 2
Earth Fault Indications
48 Earth Fault L1 A phase earth fault No set
49 Earth Fault L2 B phase earth fault No set
50 Earth Fault L3 C phase earth fault No set
51 Earth Fault Fwd Earth fault forward Not supported
52 Earth Fault Rev Earth fault reverse Not supported