Chapter 9 Maintenance Using nV-Tool
6F8C1625
84
9
Table 9-2 nV-Tool error(2)
Code
Contents
Factors
0x0103
Text parameter
error
In the specification of the transmission area,
・
Head address in Area1: beyond the limits of 0 to 511. (In the case of master station
calendar/Time setting function not used.).
・
Head address in Area1: beyond the limits of 0 to 504. (In the case of master station
calendar/Time setting function used.).
・
Area length in Area1: beyond the limits of 0 to 512. (In the case of master station
calendar/Time setting function not used.).
・
Area length in Area1: beyond the limits of 0 to 505. (In the case of master station
calendar/Time setting function used.)
・
The area specified by head address and the data length in Area1: beyond the limits of 0
to 511. (In the case of master station calendar/Time setting function not used.).
・
The area specified by head address and the data length in Area1: beyond the limits of 0
to 504. (In the case of master station calendar/Time setting function used.).
・
Head address in Area2: beyond the limits of 512 to 8703.
・
Area length in Area2: beyond the limits of 0 to 8192.
・
The area specified by head address and the data length in Area2: beyond the limits of
512 to 8703.
The com_num is not "log data clear: 1" in the operation history log command.
In time update the following state
・
Point block / point is not "point designation: 1"
・
Point number / block number is not "SYSCLOCK: 5"
・
Calendar / time data of data is abnormal
0x0104
Data read size
over
In the operation history log reading, the following state
・
The num_texts is not 5
・
The curtext_num is not 1 to 5
0x1101
STX/ETX error
Received a transmission frame whose head is not STX from nV-Tool.
Received a transmission frame whose end is not ETX from nV-Tool.
0x1102
Text size error
The transmission frame received from nV-Tool exceeds 1021 bytes.
"MsgLen" in the transmission frame received from nV-Tool does not match the length of the
actually received transmission message.
0x1104
CRC error
A transmission frame received from nV-Tool has abnormal CRC code
0x3101
Control mode
command error
During TOOL operation, RUN/HALT switch status is RUN, I/O run mode, RUN command
received from nV-Tool.
During TOOL operation, RUN/HALT switch status is RUN, down mode, RUN command
received from nV-Tool.
During TOOL operation, the RUN/HALT switch status is HALT and the RUN command or
HALT command is received from nV-Tool.
During TOOL operation, RUN/HALT switch status is RUN, HALT mode, HALT command is
received from nV-Tool.
During TOOL operation, RUN/HALT switch status is RUN, DOWN mode, HALT command
is received from nV-Tool.
During TOOL operation, receive error reset command in I/O run mode.
During TOOL operation, error reset command is received in HALT mode.
Receive the RUN command from the nV-Tool in a state where the cyclic area of the I/O
configuration information is not within the range of the cyclic area of its own node
parameter.
IReceive RUN command from nV-Tool in a state where I/O configuration information is
abnormal.
0x3102
Memory clear
command error
FL654A is set to TOOL specification; FL654A is received “memory clear” when FL654A is
I/O run mode or Down mode.
0x6102
FRAM write
error
Writing in FRAM is failure or read-out from FRAM is failure.
Failed to read I/O configuration information or own node parameters from FRAM.
Summary of Contents for FL654A
