Toshiba E-studio 477s User'S Manual And Troubleshooting Manual Download Page 60

Page: 60 / 86

Replacing Consumables / Maintenance Units

- 60 -

Turn the right blue lever of the toner
cartridge forward while pressing the top of

the toner cartridge to lock.

Close the front cover.

Please recycle a used toner cartridge.

Memo

• If you must dispose of a toner cartridge, put it in a

plastic bag or similar container and dispose of it in
accordance with your municipality's ordinances or

guidelines.

Replace Only the Image Drum (To
continue to use the toner cartridge
currently in use)

Note

• If you use a new image drum with the toner cartridges

currently in use, the remaining amount indication of the
toner cartridges will not display correctly. The messages
[Toner near Empty] or [Install new toner cartridge] may also
be displayed soon after replacement.

• The image drum (the green tube) is very delicate. Handle it

carefully.

• Do not expose the image drum to direct sunlight or very

bright interior light (approximately more than 1,500 lux).
Even under the normal interior light, do not leave it for more
than 5 minutes.

Insert your finger into the recess on the
right side of the printer and pull the front
cover open lever to open the front cover
forward.

Note

• Open the front cover gently. If you open it rapidly, the

bypass tray may open.

Pull out the image drum in the direction of
the arrow and place it on a flat surface.

Turn the right blue lever of the toner
cartridge fully in the direction of the arrow
while pressing the top of the toner cartridge
to unlock.

Print cartridge

Blue lever

Front cover

Front cover
open lever

Blue lever

Summary of Contents for E-studio 477s






















































































Search results

Summary of Contents for E-studio 477s

Reviews:

Related manuals for E-studio 477s

Brands by name

Popular brands

Toshiba E-studio 477s, User'S Manual And Troubleshooting Manual

Search results

Summary of Contents for E-studio 477s

Reviews:

Related manuals for E-studio 477s

Brands by name

Popular brands