Toshiba Carrier MMC-AP0181H2UL Service Manual Download Page 41

Page: 41 / 178

No.

Item

Recovery control for

cooling oil

(Refrigerant)

Recovery control for

heating refrigerant

(Oil)

Compensation

control for short

intermittent operation

Elimination of

retained heat

Display of filter sign
[ ]

(Not provided to the

wireless type)

∗

Separately set type

TCB-AX21UL is

prepared.

Outline of specifications

The indoor unit which is under STOP/Thermo-OFF

status or which operates in [FAN] mode performs the

following controls when it received the cooling oil

(Refrigerant) recovery signal from the outdoor unit.
1) Opens PMV of the indoor unit with a constant

opening degree.

2) Operates the indoor fan for approx. 3 minutes

during recovery control and after finish of control.

The indoor unit which is under STOP/Thermo-OFF

status or which operates in [FAN] mode performs the

following controls when it received the heating refrigerant

(Oil) recovery signal from the outdoor unit.
1) Opens PMV of the indoor unit with a constant

opening degree.

2) Stop the indoor fan.

1) For 3 minutes after start of operation, the operation

is forcedly continued even if the unit enters in

Thermo-OFF condition.

2) However the thermostat is OFF giving prior to

COOL/HEAT selection, ready for operation and

protective control.

1) When the unit stopped from [HEAT] operation, the

indoor fan operates with [L] for approx. 30 seconds.

1) The filter sign is displayed with LC by sending the

filter-reset signal to the remote controller when the

specified time (150H) elapsed as a result of integra-

tion of the operation time of the indoor fan.

2) The integrated timer is cleared when the filter-reset

signal is received from the remote controller.

In this time, if the specified time elapsed, the counted

time is reset and the LC display is deleted.

Remarks

• Recovery operation is

usually performed every

2 hours 5 minutes.

• The indoor unit which is

under thermo-OFF

(COOL) status or which

operates in [FAN] mode

stops the indoor fan and

displays [ ].

• Recovery operation is

usually performed every

1 hour.

(When there is even 1

indoor unit which the

thermo unit is off)

Usually the priority is given

to 5 minutes at outdoor

controller side.

[ FILTER] goes on.

Summary of Contents for Carrier MMC-AP0181H2UL



















































































































































































Search results

Summary of Contents for Carrier MMC-AP0181H2UL

Reviews:

Related manuals for Carrier MMC-AP0181H2UL

Brands by name

Popular brands

Toshiba Carrier MMC-AP0181H2UL, Service Manual

Search results

Summary of Contents for Carrier MMC-AP0181H2UL

Reviews:

Related manuals for Carrier MMC-AP0181H2UL

Brands by name

Popular brands