Toshiba Carrier MMC-AP0181H2UL Service Manual Download Page 124

Page: 124 / 178

124

No.

Part name

Heat

exchanger

Procedure

1. Detachment

1) Recover refrigerant gas.
2) Remove the refrigerant pipe at indoor unit

side.

3) Perform work of procedure

-1.

4) Take off screws (Ø4 × 0.31"(8mm), 3 pcs.))

fixing the piping cover to remove the piping

cover.

5) While holding the heat exchanger, remove

fixing band and fixing screws (Ø4 × 0.31"(8mm),

3 pcs.)) and then remove the heat exchanger.

2. Attachment

1) Mount parts in order, heat exchanger

→

fixing band

→

piping cover

→

drain pan

→

bell mouth

→

electric parts box as original.

NOTE)

Arrange wires as original.

2) Attach the removed connectors and wires as

original.

3) Connect the refrigerant pipe as original, and

then perform vacuuming.

Remarks

2 fixing screws for heat exchanger

Fixing band

Fixing band for
heat exchanger

Summary of Contents for Carrier MMC-AP0181H2UL



















































































































































































Search results

Summary of Contents for Carrier MMC-AP0181H2UL

Reviews:

Related manuals for Carrier MMC-AP0181H2UL

Brands by name

Popular brands

Toshiba Carrier MMC-AP0181H2UL, Service Manual

Search results

Summary of Contents for Carrier MMC-AP0181H2UL

Reviews:

Related manuals for Carrier MMC-AP0181H2UL

Brands by name

Popular brands