Toshiba BU SERIES Instruction Manual Download Page 93

Page: 93 / 94

92 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

Repair

● Repair methods

Basically, has to return it to our company when the user requests us to repair product.

In the case, exchange to a replacement or an equal function product.

● Repair request methods

On the occasion of a repair request, please return the defective product with the failure situation report sheet

to be filled out.

Please read the following instructions carefully.

1. Please return our product alone, taking out of your equipment in case that our product is installed to an

equipment

2. We are unable to return the information such as your own serial numbers, control number, the

identification seal, if it is attached to the returned products. Please keep record before you return the

product.

3. As the data saved in the camera will not be kept after the repair, please take out data before return.

4. We are unable to accept the cancellation after the repair request by the customer's reason.

5. About the repair product shipping expenses, please bear the charges when you return the product to

us. We bear the charges to you from us only for a warranty period.

6. We are unable to accept your request of a delivery date and time of the product return, or the delivery

method.

7. We are unable to accept a trouble factor investigation, the request of the repair report.

8. We accept a repair of out of warranty product, if it is reparable.

9. The proprietary rights of the repair request products after the exchange repair belong to us.

10. The immunity from responsibility of the product is applied in the repair completion products.

* Please refer for the inquiry about the software to our homepage or sales personnel.

Summary of Contents for BU SERIES





























































































Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands

Toshiba BU SERIES, Instruction Manual

Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands