Toshiba BU SERIES Instruction Manual Download Page 61

Page: 61 / 94

60 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

TimerControl

This section describes TimerControl category for the BU series.

This camera series is able to generate Timer0Active signal, derived from exposure start, by register setting.

This signal can be used as strobe control signal.

TRIG_IN

(Line0)

Exposure

TIMER0 ACTIVE

Delay

Duration

※

ActiveLow

EXPOSURE ACTIVE

Trigger

(Frame Start Trigger)

TriggerDelay

TimerTriggerSource = Line0Active

TimerTriggerSource = ExposureStart

TimerTriggerSource = FrameTrigger

Timer0Active

● Registers

Visibility

Access

Description

TimerSelector

Beginner

Returns the selected timer name.

TimerDuration

Beginner

R/W

Sets the width of Timer0Active signal.

TimerDelay

Beginner

R/W

Sets the delay of Timer0Active signal.

TimerTriggerSource

Beginner

R/W

Selects the source of Timer0Active pulse to start.

Summary of Contents for BU SERIES





























































































Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands

Toshiba BU SERIES, Instruction Manual

Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands