Toshiba BU SERIES Instruction Manual Download Page 77

Page: 77 / 94

76 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

EventControl

Camera notifies FrameTrigger status and other information by USB3 Vision Event Packet.

- FrameTrigger

: Reception of Frame Start Trigger

- FrameTriggerError

: Rejection of Frame Start Trigger

- FrameTriggerWait

: Start of waiting for Frame Start Trigger

- FrameTransferStart

: Start of transferring streaming data

- FrameTransferEnd

: End of transferring streaming data

- ExposureStart

: Start of Exposure

- ExposureEnd

: End of Exposure

- Timer0Start

: Start of Timer0

- Timer0End

: End of Timer0

Events timing are as following chart.

Overlap Trigger Reception

(1)

(6)

(7)

(6)

(7)

(6)

(7)

(1)

(4)

(5)

(4)

(5)

(4)

(5)

(3)

FrameTriggerWait will be activated before
approx. (Sensor Read Out End - Exposure Time)

(6)

(7)

(1)

(4)

(5)

(4)

(3)

(2)

(1)

(6)

(7)

This trigger is

ignored.

Overlap Trigger Rejection

Event Name

FrameTriggerWait

(Low Active)

EXT_TRIG

(Falling edge)

Exposure

Sensor Read Out

Bus Transfer

Timer0Active

(Low Active)

(8)

(9)

(8)

(9)

(8)

(9)

(8)

(9)

(8)

(9)

(3) FrameTriggerWait

(4) FrameTransferStart

(5) FrameTransferEnd

(6) ExposureStart

(7) ExposureEnd

(1) FrameTrigger

(2) FrameTriggerError

(8) Timer0Start

(9) Timer0End

: Reception of Frame Start Trigger.

: Rejection of Frame Start Trigger.

: Start of waiting for Frame Start Trigger.

: Start of transferring streaming data.

: End of transferring streaming data.

: Start of Exposure.

: End of Exposure.

: Start of Timer0.

: End of Timer0.

Summary of Contents for BU SERIES





























































































Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands

Toshiba BU SERIES, Instruction Manual

Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands