Toshiba BU SERIES Instruction Manual Download Page 28

Page: 28 / 94

27 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

● In Random Trigger Shutter mode

Image

USB Streaming

Exposure

TRIG_IN

Edge mode / Bulk mode (at all pixels readout)

Image

USB Streaming

Exposure

TRIG_IN

Level mode (at all pixels readout)

Model Name

T3 [μs]

T4 [μs]

BU302MG/MCG

15.8

29.5

BU505MG/MCG

18.8

32.6

* The value of T1 is the same as the value of normal shutter mode.

* T3 and T4 are typical value.

Notes of random trigger shutter mode:

- In the period when FRAME_TRIGGER_WAIT (GPIO signal) is inactive, user must not input external trigger signal to

this camera.

When the interval of the input trigger signal is extremely short, or when the trigger signal is noisy, there is a possibility

of causing the malfunction. In this case, please input a proper trigger signal.

Summary of Contents for BU SERIES





























































































Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands

Toshiba BU SERIES, Instruction Manual

Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands