Toshiba BU SERIES Instruction Manual Download Page 53

Page: 53 / 94

52 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

TriggerControl

This section describes trigger control of TriggerControl category for the BU series.

This camera series provides two kinds of exposure synchronization.

1. Normal Shutter mode

: Free run operation (internal synchronization)

2. Random Trigger Shutter mode : Synchronized with external trigger input

In Random Trigger Shutter mode, two kinds of trigger input are available.

1. Trigger signal via the I/O connector (HardwareTrigger)

2. Trigger command via the USB interface (SoftwareTrigger)

The following table shows the combination of operation mode of this camera series.

Table. Operation Mode

Trigger Mode

Synchronization

Exposure Control

Normal Shutter mode

Free run

“ExposureTime” register control

Random Trigger Shutter mode

HardwareTrigger

-Edge mode:TriggerSequence0

-Bulk mode:TriggerSequence6

“ExposureTime” register control

-Level mode:TriggerSequence1

Trigger pulse width control

SoftwareTrigger

-Edge mode:TriggerSequence0

-Bulk mode:TriggerSequence6

“ExposureTime” register control

* The camera operation not mentioned above is not guaranteed.

Summary of Contents for BU SERIES





























































































Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands

Toshiba BU SERIES, Instruction Manual

Search results

Summary of Contents for BU SERIES

Reviews:

Related manuals for BU SERIES

Brands by name

Popular brands