background image

71

U3U4

U1

A

U2

B

U1

A

U2

B

U1

A

U2

B

U1

A

U2

B

U1

A

U2

B

Remote controller

Remote controller

Remote controller

Header
unit

Central Control
Device

Follower unit

Follower unit

Header
unit

U1
U3 

U2
U4

U1U2 U5U6

U3U4

U3U4

U3U4

U1U2 U5U6

U1U2

U1U2 U5U6

U3U4

U1U2 U5U6

4-3-1 (8) Central control address setting

(Note)

1) Perform after the setting of indoor and outdoor unit address (Indoor/group/line address).
2) Three setting address method can be selected.

1

   Manual setting from wired main remote controller (RBC-AMT21E)

2

   Manual setting from central control remote controller (TCB-SC642TLE)

3

   Automatic setting from central remote controller (TCB-SC642TLE)

• Be sure to reconfirm the following status for all header outdoor units before the central

control address setting.

[1] Check that the relay connectors between [U1,U2] and [U3,U4] terminals are connected in

all header outdoor units to which the central control is connected.
(At the shipment from factory : No connection of connector)

[2] SW30-2 should be OFF in all header unit except the header unit with the least line address

number. (At the shipment from factory : Set to ON)

• Correct address setting can’t be conducted without the setting status above mentioned.
• The procedure above mentioned should be conducted after address setting of all indoor and

outdoor units.

REQUIREMENT

U1U2

U3U4

For inter-unit
cable between
indoor and
outdoor

For cabling of
central control
system

U5U6

For inter-unit
cable between
outdoor units

Relay 
connector

Terminator
resistor
(SW30)
Left    :SW30-1
Right :SW30-2

CPU

Interface P.C. board on the outdoor unit.

Summary of Contents for BMS-TP0640ACE









































































































Reviews: