background image

77

4-3-1 (11) Clearance of address

Method 1

An address is individually cleared from a wired remote controller.

“0099” is set up to line address, indoor address, and group address data from the remote controller.

(For the setup procedure, refer to the abovementioned address setup from the remote controller.)

Method 2

Clear the indoor addresses in the same refrigerant line from the outdoor unit.

1. Turn off the power of the refrigerant system to be returned to the status at shipment, and change the

header outdoor unit to the following status.

1) Remove the relay connector between [U1U2] and [U3U4].

(If it has been already removed, leave it as it is.)

2) Turn on SW30-2 on the interface P.C. board of the header outdoor unit if it is ON.

(If it has been already ON, leave it as it is.)

3. After “A.d. c.L.” has been displayed on 7-degment display, return SW01/SW02/SW03 to 1/1/1.

4. When the address clearing has correctly finished, “U.1.L08” is displayed on 7-degment display after a

while. If “A.d. n.G.” is displayed on 7-degment display, there is a possibility which is connected with the
other refrigerant system. Check again the relay connector between [U1U2] and [U3U4] terminals.

Note)

Be careful that the other line address may be also cleared if clearing operation is not correctly
executed.

5. After clearing of the address, set up an address again.

2. Turn on the indoor/outdoor power of which address is to be cleared. After approx. 1 minute, check that

“U.1. - - -” is displayed, and then execute the following operation on the interface P.C. board of the
header outdoor unit of which address is to be cleared in the refrigerant system.

U3 U4

U1 U2

U5 U6

U1 U2

A B

Header unit

Disconnect

Remote 

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Follower unit

Remote 

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Remote 

controller

U3 U4

U1 U2

U5 U6

U1 U2

A B

Follower unit

U3 U4

U1 U2

U1
U3

U2
U4

U5 U6

U1 U2

A B

Remote 

controller

Center unit

Center unit

Center unit

Center unit

Header unit

Header unit

Central control 

device

Unit of which address is to be returned to the initial status

Address which can be cleared

Line + Group address

Central control address

SW01 SW02 SW03

2

1

2

2

2

2

SW04

After checking that “A.d.buS” is displayed on
7-degment display, and then push SW04 for 5
seconds or more.

After checking that “A.d.nEt” is displayed on
7-degment display, and then push SW04 for 5
seconds or more.

Summary of Contents for BMS-TP0640ACE









































































































Reviews: