manualshive.com logo in svg

Toshiba 1600XP SERIES, Installation And Operation Manual

Share
Download
Toshiba 1600XP SERIES Installation And Operation Manual Download Page 53

43

1600XP/XPi Series Installation and Operation Manual – 60616-012

18.2  UPS LAN Shutdown Signal Operation 

When the UPS stop signal is sent to the UPS through pin 2 and 3 of the external contact 

interface, it is 

possible to automatically reset the following operating systems (OS), which can automatically implement 

the shutdown function and restart the operation:  

Windows NT, IBM OS/2 LAN server, LANtastic

Parameter 646 – UPS Shutdown by LAN Input Signal Enabled/Disabled
Parameter 647 – UPS Shutdown by LAN Signal Permitted Time Window (Adjustable)
With the 

UPS Shutdown by LAN Signal

 function enabled, when line power fails and the UPS goes to 

backup the LAN will shutdown even if the UPS returns to normal mode during the shutdown process.  
LAN shutdown can take several minutes.  The 

UPS Shutdown by LAN Signal

 function has a companion 

UPS Shutdown by LAN Signal Permitted Time Window

 parameter that can be set to allow sufficient 

time to complete the LAN shutdown process (default: 10 minutes) even if line power is restored during 

LAN shutdown.
LAN shutdown is treated as a restart after battery shutdown.  The restart of the LAN will be determined 

by the 

Restart After Battery Shutdown 

timer.

Connect only the UPS stop signal to the external contact interface for automatic processing so that the 

UPS output will not be turned off by mistake. 

If the computer is started/restarted within 10 minutes after the recovery from a power failure, the 
power supply may be reset while the computer is restarting.

18.3  RS-232C

The RS232C port can be used by authorized service personnel. The port is provided using a DB9 female 

connector located on the rear of the UPS. For reference, the pinout of the connector is illustrated below.

RS-232C CONNECTOR PIN ASSIGNMENT

DB9 FEMALE CONNECTOR OUTLINE 

(FACING CONNECTOR)

Pin

I/O

Symbol

Description

1

This pin is not used

2

Input

RXD

Receive data

3

Output

TXD

Transmit data

4

Output

DTR

Data terminal ready

5

-

SG

Signal ground

6

Input

DSR

Data set ready

7

Output

RTS

Request to send

8

Input

CTS

Clear to send

9

This pin is not used

Summary of Contents for 1600XP SERIES













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands