background image

Specifications

Note:

Specifications and design are subject to

change without notice.

Dimensions and Weights

Length

137 cm (54 inches)

Width

185 cm (73 inches)

Spreading width

152 cm (60 inches)

Inside clear width

175 cm (69 inches)

Height, mounted on
Workman vehicle

126 cm (49.5 inches)

Shipping weight

386 kg (850 pounds)

Dry weight

367 kg (808 pounds)

Hopper capacity

0.5 cubic meters (18 cu ft)

Required Attachments

Remote Hydraulic Control Kit (For
vehicles with serial numbers prior
to 239999999)

Model No. 07415

Engine Cover Kit (Mitsubishi,
liquid-cooled diesel Workman)

or

Part No. 92-5963

Engine Cover Kit (Mitsubishi,
liquid-cooled gas Workman)

or

Part No. 99-1214

Engine Cover Kit (Daihatsu,
liquid-cooled gas and diesel
Workman)

and

Part No. 117-4867
(Included on HD series
models)

1/3 Area Cover (Daihatsu,
liquid-cooled gas and diesel
Workman)

Note:

The 1/3 cover will not fit

if a High Air Intake Kit is installed.
A 1/3 Flat Bed must be used if a
High Air Intake Kit is installed.

or

Part No. 93-9225

1/3 Flat Bed

Model No. 07341

Recommended Accessories

Jack Stand Assembly (Qty. 4)
Requires: Hitch Pin (Qty. 4)

Part No. 105-9482-03
Part No. 100-4523

Tachometer/Speedometer Kit
(Mitsubishi, liquid-cooled gas
Workman)

Part No. 87-9950

Tachometer/Speedometer Kit
(Mitsubishi, liquid-cooled diesel
Workman)

Part No. 87-9970

Tachometer/Speedometer
Kit (air-cooled gas Workman
3000–4000)

Part No. 87-9960

Tachometer/Speedometer Kit
(air-cooled gas Workman HD)

Part No. 115-7786

Tachometer/Speedometer Kit
(Daihatsu, liquid-cooled gas
Workman 3000–4000)

Part No. 105-9498

Tachometer/Speedometer Kit
(Daihatsu, liquid-cooled diesel
Workman 3000–4000)

Part No. 105-9499

Tachometer Kit (air-cooled gas
Workman 3000–4000)

Part No. 107-7977

Tachometer Kit (Daihatsu,
liquid-cooled gas Workman
3000–4000)

Part No. 107-7975

Tachometer Kit (Daihatsu,
liquid-cooled diesel Workman
3000–4000)

Part No. 107-7976

Hand Throttle Kit (for vehicles with
serial numbers 240000001 and
up)

Model 07420

Hand Throttle Kit (for vehicles
with serial numbers prior to
239999999)

Model 07416

Attachments/Accessories

A selection of Toro approved attachments and
accessories is available for use with the machine
to enhance and expand its capabilities. Contact
your Authorized Service Dealer or authorized Toro
distributor or go to www.Toro.com for a list of all
approved attachments and accessories.

To ensure optimum performance and continued safety
certification of the machine, use only genuine Toro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous, and such use could void the
product warranty.

14

 

Summary of Contents for 44225

































Reviews: