Tone Commander 6210 User Manual Download | Manualshive

Page: 64 / 86

background image

Tone Commander 6210/6220 User Manual

61

Call Preference Options __________________

(National ISDN only)

Call Preference determines what happens when you lift the handset or
press the

Spkr

key. For Lucent 5ESS Custom ISDN service, Call

Preference is controlled by the network.

RING

preference will automatically select the oldest audibly ringing call

appearance; if there is no ringing call appearance, an idle one is
automatically selected. Call appearances that are in an alerting state,
but are not audibly ringing (refer to the Ringing Control setting above)
are not selected.

IDLE

preference always automatically selects an idle call appearance,

even if another one is ringing.

NONE

disables automatic call appearance selection; you must

manually press a Call Appearance key to originate a call.

Idle call appearances are always automatically selected for transfer
and conference operations, and when initiating calls with a Speed Dial,
DSS, REDIAL, dial pad, or UNANS key.

Call Preference must be programmed at the terminal; it is not set by a
Parameter Download.

From the User Options menu, select PREF.
(

Setup

→

USER

→

More

4

→

PREF)

Select RING, IDLE, or NONE

.

Press the

Done

key to return to the User Options menu or the

Setup

key to exit Setup Mode.

Done

CALL PREFERENCE=RINGING
RING IDLE NONE

«
...
62
63
64
65
66
...
»

Summary of Contents for 6210























































































Reviews:

No comments

Related manuals for 6210

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 396

Brand: Panasonic Pages: 68

Ascotel Office 135

Brand: Aastra Pages: 2

Brand: jablotron Pages: 2

DECT1560 Series

Brand: Uniden Pages: 64

TRU 5865 Series

Brand: Uniden Pages: 60

Brand: Tempo Fitness Pages: 6

Brand: Amplicomms Pages: 75

Brand: AT&T Pages: 52

Brand: switel Pages: 86

Linx 700-0120-501

Brand: ooma Pages: 10

Brand: Furuno Pages: 2

Brand: Topcom Pages: 21

Brand: US Robotics Pages: 70

Brand: Aastra Pages: 16

Brand: GE Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands