4 8 10 3 1 2 14
5 6 7 11 9 12 13
max 5 mm
max 5 mm
3
2
1
1 2
3
1
2
80
A=45
°
B=90
°
1
2
1
2
A B
1
4 3 5
2
Toledo
57
3. ASSEMBLY INSTRUCTIONS
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE FIGURES AT PAGE 37.
DESCRIPTION (fig. 1)
Before adjusting the saw, make sure the
tool is disconnected.
ADJUSTING THE RIVING KNIFE (fig. 2)
-
Move the blade guard backwards and lock by
means of knob (1).
-
Use a screwdriver to loosen both screws (2).
-
Adjust the riving knife, referring to the distances
indicated in the drawing.
Retighten both screws (2) and release knob (1).
-
Check that the riving knife is exactly behind the
blade.
ADJUSTING THE CUTTING ANGLE (fig. 3)
-
Loosen both knobs (1).
-
Move the shoe (2) into the proper position (0°-
45°). The cutting angle is indicated by the pointer
(3).
ADJUSTING THE DEPTH OF CUT (fig. 4)
-
Loosen knob (1).
-
Move the shoe (2) downwards.
-
The depth of cut can be checked (3).
-
After adjustment retighten knob (1).
MOUNTING THE PARALLEL GUIDE (fig. 5)
-
Loosen knob (1).
-
Insert the guide into the relevant recesses (2).
-
Set the required width and retighten knob (1).
REPLACING OR CLEANING THE BLADE
(fig. 6)
Before adjusting the saw, make sure the
tool is disconnected.
-
Move the blade guard backwards and lock by
means of knob (1).
-
Lock-up the shaft with the spindle lock.
-
Use an hexagonal key (2) to loosen the left-hand
bolt in the centre of the blade.
-
Remove the blade and clean or replace.
-
Put the blade back in its proper position, making
sure the teeth of the blade point in the same direc-
tion as those of the riving knife (4).
Fit the locking ring (5) and retighten the left-hand
bolt.
After fitting a new blade it may be necessa-
ry to readjust the riving knife.
-
Release knob (1) to put the guard back in place.
REPLACING THE CARBON BRUSHES (fig. 7):
Frequent use will cause the carbon brus-
hes to wear down. Regular inspection, after
every 100 hours of use, is essential. If the
brushes have worn down to less than 4mm,
replace.
-
Remove both screws (1).
-
Take the brushes (2) out and check.
-
Reinsert the brushes into the relevant recesses.
Make sure the copper part of the brushes firmly
touches the copper part in the recess.
-
Retighten the screws (1).
SWITCHING ON/OFF (fig.7)
-
Depress knob (B) with your right-hand thumb
and keep it depressed.
-
Depress knob (A) to start the tool.
-
Release knob (A) to stop the tool.
!
!
!
!
1. Handle
2. Spindle lock
3. On/off switch
4. Depth of cut adjusting
knob
5. Mains lead
6. Riving knife
7. Blade guard
8. Hexagonal bolt
9. Shoe
10. Flange
11. Saw Blade
12. Parallel stop
13. Parallel guide adjus-
ting knob
14. Cutting angle adjus-
tingknob
4
Toledo
FIG. 1
FIG. 2
FIG. 3
FIG. 4
FIG. 5
FIG. 6
FIG. 7
45
30
0
1
2
3
3 4
