Toho Electronics TRM20A Operation Manual Download Page 126

Page: 126 / 146

9-1

．

MAINTENANCE

9.1 Inspection

In order to effectively use the instrument, please inspect periodically.

Inspection item

Inspection description

Remark

Measurement value

- Correct measurement value has been displayed?

Display

- The brightness of the backlight appropriate?

- Is there lack and blur on the display?

Recording data

- Measurement value indication and data storing have

been correctly?

clock

- Is the clock display view the correct time?

Installation condition

- Is there looseness or damage in mounting bracket?

Wiring condition

- Is there looseness or damage in terminal screw?

9.2 Recommended replacement cycle of parts

Names of parts

Cycle

Remark

Lithium Battery

5 years

(20°C without being used.)

A user cannot replace the battery. Contact

our dealer where you purchased the

instrument, or our sales representative.

Summary of Contents for TRM20A


















































































































































Search results

Summary of Contents for TRM20A

Reviews:

Toho Electronics TRM20A, Operation Manual, Page: 126 / 146

Search results

Summary of Contents for TRM20A

Reviews: