manualshive.com logo in svg

Toho Electronics TRM20A, Operation Manual, Page: 107 / 146

Share
Download
Toho Electronics TRM20A Operation Manual Download Page 107

 

8-20 

8.16  Setting the LCD sleep time 

［

Explanation

］

 

LCD is automatically turned off when there is no operation in the main body for a fixed time. 

 

［

Operation

］

 

Select the Device/Other key 

⇒

  LCD key on the System. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

①

 

Sleep time 
Time until changing to brightness to which LCD is set by “

③

Sleep brightness” is set. 

(0 to 60 min) 
Please input an arbitrary “Sleep time” from the numeric input screen, and set it with the OK key. 
(When 0 is input, the sleep function is not used.) 

②

 

Act. brightness 
LCD sets the numerical value of the brightness when it is active. It lightens by the numerical 
value large. 
Please input an arbitrary “Act. brightness (2

～

5)” from the numeric input screen, and set it with 

the OK key. 

③

 

Sleep brightness 
LCD sets the numerical value of the brightness when it is sleep. It lightens by the numerical value 
large. 
Please input an arbitrary “Sleep brightness (0

～

4)” from the numeric input screen, and set it with 

the OK key. 

④

 

Alarm Recovery (It supports since recorder version 1.20.) 
If an alarm occurs at the time of LCD OFF, LCD is turned ON automatically.   
(While the alarm has occurred, regardless of [

①

Sleep time], LCD is always ON.

 

LCD becomes 

"off" when the setup time of [

①

Sleep time] passes. (Not operating) 

 

 

①

Sleep time 

 
 
 

②

Act. brightness 

 
 
 

③

Sleep brightness 

 
 
 

④

Alarm Recovery 

 
 
 

Summary of Contents for TRM20A



















































































































































Reviews:

No comments