Toho Electronics TRM20A Operation Manual Download Page 11

Page: 11 / 146

2-1

．

NAMES AND FUNCTIONS OF PARTS

2.1

Names and functions of parts

①

Display area

The LCD is provided with touch panel. Display the measurement data and other various
Parameter set screens. Touch the surface to set data.

②

Button operation part cover

This panel protects the button operation part. It pulls it forward while pushing two knobs below to
appear function keyboard.
Note: Please do the both hands to the opening and shutting of cover. It causes damage.

Please be performed in both hands open and close the cover.
It causes the damage.

During the opening and closing of the cover, please be careful not to pinch
your fingers.

①

Display Unit

②

Button operation part cover

Knob

【

When opening cover of button operation part

】

【

When closing cover of button operation part

】

CAUTION

Summary of Contents for TRM20A


















































































































































Search results

Summary of Contents for TRM20A

Reviews:

Toho Electronics TRM20A, Operation Manual, Page: 11 / 146

Search results

Summary of Contents for TRM20A

Reviews: