TigerStop TigerSaw 1000 Installation Manual Download Page 56 | Manualshive

Page: 56 / 68

background image

53

2. Loosen the idler pulley bolt and remove belt.

Note: Do NOT take bolt all the way out

3. When replacing the belt, pull down on the idler pulley to tension the belt.

Changing the Cap Guard

1. Remove the saw guard top

Note: For more details, see Guard Installation on page 23.

2. Remove the air cylinder link from the top cap and remove the top cap bolts. Once loose, slide the

top cap off of the guides.

3. Remove the top cap brackets and replace wood top cap.

«
...
54
55
56
57
58
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

Brand: Ecco Pages: 4

Brand: JD Squared Pages: 15

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

Brand: CAIRE Pages: 2

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: Jacobsen Pages: 20

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Tanco Pages: 112

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Brand: Wassermann Pages: 24

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands