TigerStop TigerSaw 1000 Installation Manual Download Page 51 | Manualshive

Page: 51 / 68

background image

48

Printer Adjustments

The TigerSaw 1000 evolution ink jet printer has a height adjustment to control the height of the print

printer head. It is critical that the printer be as close to the material as possible.

Printer Height Adjustment

To adjust printer height...
1. Put a piece of material under the printer head.
2. Loosen the locking handle and allow the printer wheel to touch your material.
3. Raise the printer by about .125 inch or less.
4. Tighten the locking handle.

Note: Printer height is critical to print quality.

Cleaning the Printer

The evolution ink jet printer has disposable ink cartridges that house the ink jets. The ink jets can

be cleaned if necessary.

To clean the printer...
1. Simply use a dry paper towel and wipe the printer ink jets in a motion parallel to the ink jets.
2. If the print quality is still low, you may need to change the ink cartridge.

UV Sensor Adjustment

The UV sensor on the TigerStop pusher foot can be adjusted in both sensitivity and sensor height.

Locking Handle

«
...
49
50
51
52
53
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Dynapro ET 355 Monitor HL

Brand: 3M Pages: 23

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Baker Pages: 82

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: Taylor Pages: 60

Brand: TANDBERG Pages: 23

Brand: Keller Pages: 12

Brand: MacDon Pages: 49

Brand: MacDon Pages: 49

Brand: MacDon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands