TigerStop TigerSaw 1000 Installation Manual Download Page 50 | Manualshive

Page: 50 / 68

background image

47

Warning! Do not take out bolts A and B. Doing so will damage TigerSaw!

Adjust Cycle Height

TigerSaw 1000 has two sensors mounted to the saw cycle cylinder. The top sensor controls saw

cycle height. Ensure TigerSaw is properly locked out/tagged out before performing any adjustments.

1. Open the side access door and locate the saw cycle cylinder.
2. This cylinder has 2 sensors attached to it.
3. Loosen one of the screws holding the top sensor tight to the cylinder.
4. Move the sensor up or down.
5. Tighten the screw once the sensor is in place.

The sensor lights up when it senses the saw blade. Watch the light for the few first cycles. If the

light is yellow, it means that the sensor is on the edge of its sensing range. Adjust the sensor sideways
until this light is green.

Top Cap Travel Adjustment

The range of movement on the top cap can be adjusted to suit the material you are cutting.

To adjust the top cap travel...
1. Turn the saw blade off using the red portion of the power switch marked “Saw”.
2. Loosen the locking handle as shown.
3. Turn the height adjustment wheel to adjust the top cap stopper.
4. Power the saw blade up to apply air pressure and test the top cap travel.
5. Repeat if necessary.

«
...
48
49
50
51
52
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Haenim Pages: 2

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Bahco Pages: 9

Brand: Kärcher Pages: 88

Brand: Oakworks Medical Pages: 28

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: TATU Pages: 30

Brand: Rane Pages: 4

Brand: Sabio Pages: 182

Brand: Xycom Pages: 65

Brand: Xtool Pages: 8

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands